View TEA1553T_3501435.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1. general description the greenchip ii is the second generation of green switched mode power supply (smps) controller ics operating directly from the recti?ed universal mains. a high level of integration leads to a cost effective power supply with a very low number of external components. the special built-in green functions allow optimum ef?ciency at all power levels. this applies to quasi-resonant operation at high power levels, as well as ?xed frequency operation with valley switching at medium power levels. at low power (standby) levels, the system operates at reduced frequency and with valley detection. the proprietary high voltage bcd800 process makes direct start-up possible from the recti?ed universal mains voltage in an effective and green way. a second low voltage bicmos ic is used for accurate, high speed protection functions and control. highly ef?cient, reliable supplies can easily be designed using the greenchip ii controller. 2. features 2.1 distinctive features n universal mains supply operation (70 v ac to 276 v ac) n high level of integration, giving a very low external component count 2.2 green features n valley/zero voltage switching for minimum switching losses n frequency reduction at low power standby for improved system ef?ciency (< 1 w) n on-chip start-up current source n ef?cient quasi-resonant operation at high power levels n cycle skipping mode at very low loads; input power < 300 mw at no-load operation for a typical adapter application n standby indication pin to indicate low output power consumption 2.3 protection features n safe restart mode for system fault conditions n continuous mode protection by means of demagnetization detection (zero switch-on current) n accurate and adjustable versatile overvoltage protection (ovp) (latched) n short winding protection n undervoltage protection (foldback during overload) TEA1553T greenchip ii smps control ic rev. 01 3 july 2007 product data sheet
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 2 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic n overtemperature protection (otp) (latched) n low and adjustable overcurrent protection (ocp) trip level n general purpose lock input for external protection n mains voltage-dependent operation-enabling level n soft (re)start n advanced overpower protection (opp) functions 3. applications besides typical application areas, i.e. adapters and chargers, the device can be used in all applications that demand an ef?cient and cost effective solution up to 250 w. 4. ordering information table 1. ordering information type number package name description version TEA1553T so16 plastic small outline package; 16 leads; body width 3.9 mm sot109-1
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 3 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic 5. block diagram fig 1. block diagram of TEA1553T gnd stdby 9 11 uvlo drain 8 logic logic 4 vcoadj ctrl 1 hvs 6, 7 dem 16 + clamp i vcoadj 2 q q s r leb blank q q s r uvlo 14 15 13 s2 5 3 s3 12 lock TEA1553T s1 + 80 mv 014aaa004 v cc v mains(oper)(en) internal supply start voltage controlled oscillators supply management start up current source valley frequency control overvoltage protection up/down counters i prot(ctrl) power-on reset 0.88 v overpower protection maximum on-time protection driver 300 w 5.6 v ovpfcap driver i startup(soft) 0.5 v cstart 300 w 300 w 5.6 v 5.6 v minimum freq. enabling and timing 2.5 v lock detect overtemperature protection vcc < 4.5 v enable/disable i aop 0.5 v advanced overpower protection isense vcc5v 5 v/1 ma (max) - 1
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 4 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic 6. pinning information 6.1 pinning 6.2 pin description fig 2. pin con?guration for TEA1553T TEA1553T dem ctrl stdby lock driver hvs gnd hvs drain 014aaa000 1 2 3 4 5 6 7 8 10 9 12 11 14 13 16 15 vco adj ovpfcap isense cstart vcc5v n.c. vcc table 2. pin description symbol pin description vcoadj 1 voltage controlled oscillator (vco) adjustment input ovpfcap 2 ovp ?lter timing capacitor isense 3 programmable current sense input stdby 4 standby control output driver 5 gate driver output hvs 6 high voltage safety spacer, not connected hvs 7 high voltage safety spacer, not connected drain 8 drain of external mos switch, input for start-up current and valley sensing v cc 9 supply voltage n.c. 10 not connected gnd 11 ground vcc5v 12 5 v output lock 13 lock input (general purpose input for switching off the ic). ctrl 14 control input cstart 15 ipeak reduction timing capacitor dem 16 input from auxiliary winding for demagnetization timing, ovp and opp
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 5 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic 7. functional description the TEA1553T is a controller for a compact ?yback converter, with the ic situated on the primary side. an auxiliary winding of the transformer provides demagnetization detection and powers the ic after start-up. the TEA1553T operates in multi modes, see figure 4 . (1) if a 600 v mosfet is used, the drain connection can be made directly to the vin; a center-tap from the transformer is not necessary. fig 3. basic application 1 2 3 4 5 6 7 8 10 9 12 11 14 13 16 15 TEA1553T output 014aaa001 v mains power mosfet r sense dem ctrl lock gnd vcc n.c. vcc5v cstart stdby driver hvs hvs drain isense ovpfcap vcoadj r dem
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 6 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic the next converter stroke is started only after demagnetization of the transformer current (zero current switching), while the drain voltage has reached the lowest voltage to prevent switching losses (green function). the primary resonant circuit of primary inductance and drain capacitor ensures this quasi-resonant operation. the design can be optimized in such a way that zero voltage switching can be achieved over almost the whole of the universal mains range. to prevent very high frequency operation at lower loads, the quasi-resonant operation changes smoothly in ?xed frequency pulse width modulation (pwm) control. at low power levels, the frequency is controlled via the voltage controlled oscillator (vco), down to a minimum of about 25 khz. at very low power levels (standby), a cycle skipping mode will be activated. 7.1 start-up, mains enabling operation level and undervoltage lock-out initially, the ic is self-supplying from the recti?ed mains voltage via pin drain. supply capacitor c vcc is charged by the internal start-up current source to a level of about 4 v or higher, depending on the drain voltage. once the drain voltage exceeds v mains(oper)(en) (mains-dependent operation-enabling voltage), the start-up current source will continue charging capacitor c vcc (switch s1 will be opened); see figure 1 . the ic will activate the power converter as soon as the voltage on pin v cc passes the v startup level. the ic supply is taken over by the auxiliary winding as soon as the output voltage reaches its intended level and the ic supply from the mains voltage is subsequently stopped for high ef?ciency operation (green function). the moment the voltage on pin v cc drops below the v th(uvlo) (undervoltage lock-out) level, the ic stops switching and enters a safe restart from the recti?ed mains voltage. inhibiting the auxiliary supply by external means causes the converter to operate in a stable, well de?ned burst mode. (see figure 14 and figure 15 ). 7.2 supply management all (internal) reference voltages are derived from a temperature compensated, on-chip band gap circuit. fig 4. multi mode operation fixed 014aaa002 quasi-resonant 125 khz f vco 25 khz power
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 7 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic 7.3 current mode control current mode control is used for its good line regulation behavior. the on-time, is controlled by the internally inverted control pin voltage, which is compared with the primary current information. the primary current is sensed across an external resistor. the driver output is latched in the logic, preventing multiple switch-on. the internal control voltage is inversely proportional to the external control pin voltage, with an offset of 1.5 v. this means that a voltage range from 1 to 1.5 v on pin ctrl will result in an internal control voltage range from 0.5 v to 0 v (a high external control voltage results in a small duty cycle). 7.4 oscillator the maximum ?xed frequency of the oscillator is set by an internal current source and capacitor. the maximum frequency is reduced once the control voltage enters the vco control window. it then changes linearly with the control voltage until the minimum frequency is reached (see figure 5 and figure 6 ). fig 5. the v sense(max) voltage as a function of v ctrl fig 6. the vco frequency as a function of v sense (max) 014aaa003 0.52 v 1 v (typ) 1.5 v (typ) v sense(max) v ctrl 0 14 aaa005 f 25 khz 125 khz vco 2 level vco 1 level v sense(max)
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 8 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic 7.5 vco adjust the vcoadj pin can be used to set the vco operation point. as soon as the peak voltage on the sense resistor is controlled below half the voltage on the vcoadj pin (vco 1 level), frequency reduction will start. (the actual peak voltage on r sense will be somewhat higher due to switch-off delay, see figure 8 .) the frequency reduction will stop about 50 mv lower (vco 2 level), when the minimum frequency is reached. a current of typically 10 m a ?ows out of the vcoadj pin, enabling the vco operation point to be set with a single resistor. when a more low-ohmic connection is desired (e.g. due to noise), a voltage divider can be made from the vcc5v pin (see figure 7 ). fig 7. implementation of stdby and cycle skipping functionality ctrl oscillator v i 2 vx 1.5 v - v ctrl current comparator driver 5 v driver isense vcc5v vcoadj 014aaa006
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 9 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic 7.6 cycle skipping at very low power levels, a cycle skipping mode will be activated. a high control voltage will reduce the switching frequency to a minimum of 25 khz. if the voltage on the control pin is raised even more, switch-on of the external power mosfet will be inhibited until the voltage on the control pin has dropped to a lower value again (see figure 8 ). for system accuracy, the absolute voltage on the control pin is not used to trigger the cycle skipping mode. instead, a signal derived from the internal vco will be used. if the no-load requirement of the system is such that the output voltage can be regulated to its intended level at a switching frequency of 25 khz or above, the cycle skipping mode will not be activated. 7.7 stdby output the stdby output pin can be used to drive an external npn or fet, v stdby = 5 v, in order to switch off a power factor correction (pfc) circuit. the stdby output is activated by the internal vco: as soon as the vco has reduced the switching frequency to almost the minimum frequency of 25 khz, the stdby output will be activated (see figure 8 ). the stdby output will go low again as soon as the vco allows a switching frequency close to the maximum frequency of 125 khz. (1) the voltage levels dv 1 , dv 2 , dv 3 and dv 4 are ?xed in the ic to 50 mv (typ.), 18 mv (typ.), 40 mv (typ.) and 15 mv (typ.) respectively. the level at which the vco mode of operation starts/ends can be externally controlled with the vcoadj pin. fig 8. signal diagram for stdby and cycle skipping functionality vx (v) vx (v) vx (v) stdby (v) cycle skipping 5 0 f s (khz) f max f min dv 2 dv 1 dv 3 dv 4 vcoadj 1 0 014aaa007
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 10 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic 7.8 demagnetization the system will be in discontinuous conduction mode all the time. the oscillator will not start a new primary stroke until the secondary stroke has ended. demagnetization features a cycle-by-cycle output short-circuit protection by immediately lowering the frequency (longer off-time), thereby reducing the power level. demagnetization recognition is suppressed during the ?rst t sup(xfmr_ring) time. this suppression may be necessary in applications where the transformer has a large leakage inductance and at low output voltages/start-up. 7.9 overvoltage protection an ovp mode is implemented in the greenchip series. for the TEA1553T, this works by sensing the auxiliary voltage via the current ?owing into pin dem during the secondary stroke. the auxiliary winding voltage is a well-de?ned replica of the output voltage. any voltage spikes are averaged by an internal ?lter. pin ovpfcap is used to program the ovp function as follows: 1. pin grounded: ovp is disabled. 2. pin at 5 v (e.g. connected to pin 12, the vcc5v pin): the internal ovp circuit is enabled. 3. a capacitor is connected from the pin to the ground: this capacitor is used to set the number of ovp events that can occur before the logic determines that an actual ovp condition exists. the minimum timing is the internal ovp timing. in the last case, the number of ovp events can be set by an external capacitor connected to pin ovpfcap: where n is the number of ovp counts which are allowed to occur before an actual ovp state is detected. if the output voltage exceeds the ovp trip level, an internal counter starts counting subsequent ovp events. the counter has been added to prevent incorrect ovp detections which could occur during esd / lightning events. if the output voltage exceeds the ovp trip level a few times, and then does not exceed it in the next cycle, the internal counter will count down twice as fast as it counted up. however, when typically 10 cycles of subsequent ovp events are detected, the ic assumes a true ovp state exists and the ovp circuit switches the mosfet off. next, the controller waits until the v th(uvlo) level is reached on pin v cc , and then capacitor c vcc is recharged to the v startup level. operation only recommences when the v cc voltage drops below a level of about 4.5 v, in practice this only occurs when the mains input voltage has been disconnected for a short period of time the output voltage at which the ovp function trips, v trip(ovpfcap) , can be set by the demagnetization resistor, r dem : c ovp n i ch ovpfcap () t p ovpfcap () v ovpfcap --------------------------------------------------------------------- - =
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 11 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic where n s is the number of secondary turns and n aux is the number of auxiliary turns of the transformer. current i ovp is internally trimmed. the value of the demagnetization resistor, r dem , can be adjusted to the turns ratio of the transformer, thus making an accurate ovp possible. 7.10 valley switching (see figure 9 .) a new cycle starts when the power switch is switched on. after the on-time (which is determined by the sense voltage and the internal control voltage), the switch is opened and the secondary stroke starts. after the secondary stroke, the drain voltage shows an oscillation with a frequency of approximately where l p is the primary self inductance of the transformer and c d is the capacitance on the drain node. as soon as the oscillator voltage is high again and the secondary stroke has ended, the circuit waits for the lowest drain voltage before starting a new primary stroke. this method is called valley detection. figure 9 shows the drain voltage together with the valley signal, the signal indicating the secondary stroke and the oscillator signal. in an optimum design, the re?ected secondary voltage on the primary side will force the drain voltage to zero. thus, zero voltage switching is possible, preventing large capacitive losses , and allowing high frequency operation, which results in small and cost effective inductors. v trip ovpfcap () n s n aux ----------- i ovp r dem v cl pos () + ) ( = 1 2 p l p c d ) ( ) ( ----------------------------------------------------- p 1 2 -- - cv 2 f = ? ? ?
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 12 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic 7.11 overcurrent protection the cycle-by-cycle peak drain current limit circuit uses the external source resistor to measure the current accurately. this allows optimum size of the transformer core to be determined (cost issue). the circuit is activated after the leading edge blanking time, t leb . the ocp protection circuit limits the sense voltage to an internal level. 7.12 overpower protection during the primary stroke, the recti?ed mains input voltage is measured by sensing the current drawn from pin dem. this current is dependent on the mains voltage, according to the following formula: where: the current information is used to adjust the peak drain current, which is measured via pin isense. the internal compensation is such that a maximum output power can be achieved that is almost mains independent. (1) start of new cycle at lowest drain voltage. (2) start of new cycle in a classical pwm system at high drain voltage. fig 9. signals for valley switching drain secondary stroke 014aaa027 secondary ringing primary stroke valley (2) (1) secondary stroke oscillator i dem v aux r dem -------------- nv mains r dem -------------------------- - ?? n n aux n p ----------- =
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 13 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic the opp curve is given in figure 10 . 7.13 advanced overpower timing via pin cstart overload conditions might lower the switching frequency below 20 khz, since demagnetization prevents next cycle occurrence before the transformer current reaches zero (demagnetization protection). to prevent audible noise, an extra timer of typically 25 khz is added. when the timer is activated (the frequency is typically below 25 khz), a current (i aop ) of approximately 10 m a is injected into the external soft-start resistor and capacitor. the current that is being injected is dependent on the v sense voltage and the duty cycle, see also figure 11 and figure 12 . the current injection results in a decrease of the primary peak current and a higher frequency. the injection is only possible when the voltage on the control pin is below 0.5 v and the cstart voltage is above 2.5 v. the current injection is disabled when v ctrl > 0.5 v (that is, in normal operation and also in frequency reduction mode), during start-up (cstart timing) and when v sense > 0.5 v. fig 10. opp correction curve - 500 m a (typ) i dem - 120 m a (typ) v sense(max) 0.52 v (typ) 0.30 v (typ) 014aaa009 fig 11. i aop as a function of v sense 014aaa010 10 7.5 5 0.5 i aop ( m a) v sense(v) d ~ 50% d ~ 0%
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 14 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic the charging current, i opp(adv) , will ?ow as long as the voltage on pin isense is below approximately 0.5 v. if it exceeds this value, the current source will start to limit the current i opp(adv) . 7.14 minimum and maximum on-time the minimum on-time of the smps is determined by the leading edge blanking (leb) time. the ic limits the maximum on-time to 50 m s. when the system requires an on-time longer than 50 m s, a fault condition is assumed (e.g. c i has been removed), the ic will stop switching and enter the safe restart mode. 7.15 short winding protection after the leading edge blanking time, the short winding protection circuit is also activated. if the sense voltage exceeds the short winding protection voltage, v swp , the converter will stop switching. once v cc drops below the v th(uvlo) level, capacitor c vcc will be recharged and the supply will restart again. this cycle will be repeated until the short circuit is removed (safe restart mode). the short winding protection will also protect in case of a secondary diode short circuit. 7.16 lock input pin 13 is a general purpose (high impedance) input pin, which can be used to switch off the ic. as soon as the voltage on this pin is raised above 2.5 v, switching will stop immediately. the voltage on the v cc pin will cycle between v startup and v th(uvlo) , but the ic will not start switching again until the latch function is reset. the latch is reset as soon as v cc drops below 4.5 v (typical value). the internal ovp and otp will also trigger this latch (see figure 3 ). the detection level of this input is related to the vcc5v pin voltage in the following way: 0.5 v vcc5v 4 %. an internal zener clamp of 5.6 v will protect this pin from excessive voltages. no internal ?ltering is done on this input. fig 12. advanced overpower current injection 014aaa011 i aop f aop 0.5 v v ocp 100 k w gate ( d ) isense r ss c ss r sense driver
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 15 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic 7.17 overtemperature protection an accurate temperature protection is provided in the circuit. when the junction temperature exceeds the thermal shutdown temperature, the ic will stop switching. when v cc drops to v th(uvlo) , capacitor c vcc will be recharged to the v startup level, however the ic will not start switching again. subsequently, v cc will drop again to the v th(uvlo) level, and so on. operation only recommences when the v cc voltage drops below a level of about 4.5 v, in practice this only occurs when the mains input voltage has been disconnected for a short period of time. 7.18 5 v output pin 12 can be used for the supply of external circuitry. the maximum output current must be limited to 1 ma. if higher peak currents are required, an external rc combination should limit the current drawn from this pin to 1 ma maximum. the 5 v output voltage will be available as soon as the start-up voltage is reached. as the high voltage supply cannot supply the vcc5v pin during start-up or shutdown, during latched shutdown (via pin 13 or other latched protection such as ovp or otp), the voltage is switched to zero. 7.19 open/not connected ctrl pin protection if the ctrl pin is open/not connected, a fault condition is assumed and the converter will stop switching. operation will recommence as soon as the fault condition is removed. 7.20 soft start-up (pin isense) to prevent transformer rattle during hiccup, the transformer peak current through the sense resistor, i dm , is slowly increased by the soft start function. this can be achieved by inserting a resistor and a capacitor between pin isense (pin 3) and the sense resistor, r sense . an internal current source charges the capacitor to v = i startup(soft) r ss , with a maximum of about 0.5 v. the start level and the time constant of the increasing primary current level can be adjusted externally by changing the values of r ss and c ss . the charging current i startup(soft) will ?ow as long as the voltage on pin isense is below approximately 0.5 v. if the voltage on pin isense exceeds 0.5 v, the soft start current source will start limiting the current i startup(soft) . at the v startup level, the i startup(soft) current source is completely switched off (see figure 13 ). since the soft start current i startup(soft) is subtracted from pin v cc charging current, the r ss value will affect the v cc charging current level by a maximum of 60 m a (typical value). i dm v sense max () i startup soft () r ss ) ( C r sense ---------------------------------------------------------------------------------- = t r ss c ss =
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 16 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic 7.21 driver the driver circuit to the gate of the power mosfet has a current sourcing capability of typically 170 ma and a current sink capability of typically 700 ma. this permits fast turning on and off of the power mosfet for ef?cient operation. a low driver source current has been chosen to limit the d v/ d t at switch-on. this reduces the electromagnetic interference (emi) and also limits the current spikes across r sense . fig 13. soft start-up isense 014aaa012 i startup(soft) 0.5 v startup r ss c ss overcurrent protection voltage r sense driver
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 17 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic 8. limiting values table 3. limiting values in accordance with the absolute maximum rating system (iec 60134). all voltages are measured with respect to ground (pin 11); positive currents ?ow into the chip; pin v cc may not be current driven. the voltage ratings are valid provided other ratings are not violated; current ratings are valid provided the maximum power rating is not violated. symbol parameter conditions min max unit voltages v vcoadj voltage on pin vcoadj input voltage; continuous - 0.4 +5 v v ovpfcap voltage on pin ovpfcap continuous - 0.4 +7 v v isense voltage on pin isense current limited - 0.4 - v v drain voltage on pin drain - 0.4 +650 v v cc supply voltage continuous - 0.4 +20 v v lock voltage on pin lock continuous - 0.4 +7 v v ctrl voltage on pin ctrl - 0.4 +5 v v cstart voltage on pin cstart - 0.4 +7 v v dem voltage on pin dem current limited - 0.4 - v currents i isense current on pin isense input current - 1 +10 ma i stdby current on pin stdby - 1- ma i driver current on pin driver d < 10 % - 0.8 +2 a i drain current on pin drain -+5ma i o(vcc5v) output current on pin vcc5v - 10 ma i ctrl current on pin ctrl -+5ma i dem current on pin dem - 1.25 +1.25 ma general p tot total power dissipation t amb < 70 c - 0.7 w t stg storage temperature - 55 +150 c
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 18 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic [1] equivalent to discharging a 100 pf capacitor through a 1.5 k w series resistor. [2] equivalent to discharging a 200 pf capacitor through a 0.75 m h coil and a 10 w resistor. 9. thermal characteristics 10. characteristics t j junction temperature - 20 +145 c esd v esd electrostatic discharge voltage class 1 human body model pins 1 to 7 and pins 9 to 16 [1] - 2000 v pin 8 (drain) [1] - 1500 v machine model [2] - 200 v table 3. limiting values in accordance with the absolute maximum rating system (iec 60134). all voltages are measured with respect to ground (pin 11); positive currents ?ow into the chip; pin v cc may not be current driven. the voltage ratings are valid provided other ratings are not violated; current ratings are valid provided the maximum power rating is not violated. symbol parameter conditions min max unit table 4. thermal characteristics symbol parameter conditions typ unit r th(j-a) thermal resistance from junction to ambient in free air 110 k/w table 5. characteristics t amb = 25 c; v cc = 15 v; all voltages are measured with respect to ground (pin 11); currents are positive when ?owing into the ic, unless otherwise speci?ed. symbol parameter conditions min typ max unit start-up current source (pin 8) i drain current on pin drain input current; v cc = 0 v; v i on pin drain > 100 v 1.0 1.2 1.4 ma with auxiliary supply; v i on pin drain > 100 v - 100 300 m a v br breakdown voltage 650 - - v v mains(oper)(en) mains-dependent operation-enabling voltage 60 - 100 v v cc management (pin 9) v startup start-up voltage 10.3 11 11.7 v v th(uvlo) undervoltage lockout threshold voltage 8.1 8.7 9.3 v v hys hysteresis voltage v startup - v th(uvlo) 2.0 2.3 2.6 v
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 19 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic i ch(high) high charging current v i on pin drain > 100 v; v cc < 3 v - 1.2 - 1 - 0.8 ma i ch(low) low charging current v i on pin drain > 100 v; 3 v < v cc < v th(uvlo) - 1.2 - 0.75 - 0.45 ma i restart restart current v i on pin drain > 100 v; v th(uvlo) < v cc < v startup - 650 - 550 - 450 m a i cc(oper) operating supply current no load on pin driver 1.1 1.3 1.5 ma demagnetization management (pin 16) v dem voltage on pin dem 50 80 110 mv v cl(neg) negative clamp voltage voltage on pin dem, i i on pin dem = - 500 m a - 0.5 - 0.25 - 0.05 v v cl(pos) positive clamp voltage voltage on pin dem, i i on pin dem = 1 ma 0.5 0.7 0.9 v t sup(xfmr_ring) transformer ringing suppression time 1.1 1.5 1.9 m s pulse width modulator t on(min) minimum on-time - t leb -ns t on(max) maximum on-time 40 50 60 m s oscillator f osc(low) low oscillator frequency v i on pin ctrl > 1.5 v 20 25 30 khz f osc(high) high oscillator frequency v i on pin ctrl < 1 v 100 125 150 khz v vco(start) start vco voltage peak voltage at pin isense, where frequency reduction starts. see figure 6 and figure 8 - vco 1 -mv v vco(max) maximum vco voltage peak voltage at pin isense, where the frequency is equal to f osc(low) - vco 1 - 50 - mv duty cycle control (pin 14) v min( d max) minimum voltage (maximum duty cycle) - 1.0 - v v max( d min) maximum voltage (minimum duty cycle) - 1.5 - v i ctrl current on pin ctrl input current, v i on pin ctrl = 1.5 v - 1 [1] - 0.8 - 0.5 m a 5 v output (pin 12) v o(vcc5v) output voltage on pin vcc5v current on pin vcc5v = - 1ma 4.75 5.0 5.25 v i o(vcc5v) output current on pin vcc5v - 1.0 - - ma lock input (pin 13) table 5. characteristics continued t amb = 25 c; v cc = 15 v; all voltages are measured with respect to ground (pin 11); currents are positive when ?owing into the ic, unless otherwise speci?ed. symbol parameter conditions min typ max unit
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 20 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic v trip trip voltage 2.37 2.5 2.63 v v vcc(latch)(reset) latch reset voltage on pin v cc v trip < 2.3 v - 4.5 - v v lock /v vcc5v voltage on pin lock to voltage on pin vcc5v ratio v trip = 0.5 v o( vcc5v) - 4 - +4 % advanced overpower timing via pin cstart (pin 15) i ch(cstart) charge current on pin cstart - 11.5 - 10 - 8.5 m a v trip(cstart) trip voltage on pin cstart 2.37 2.5 2.63 v i opp(adv) advanced over-power protection current v i on pin sense < 0.1 v - 11.5 - 10 - 8.5 m a f act(opp)(adv) advanced over-power protection activation frequency v i on pin ctrl < 0.5 v and v i on pin cstart > 2.5 v 20 25 33 khz vcoadj input (pin 1) i vcoadj current on pin vcoadj - 11.5 - 10 - 8.5 m a valley switch (pin 8) ( d v/ d t) vrec valley recognition voltage change with time - 85 - +85 v/ m s t d(vrec-swon) valley recognition to switch-on delay time - 150 [1] -ns current and short winding protection (pin 3) v sense(max) maximum sense voltage d v/ d t = 0.1 v/ m s 0.48 0.52 0.56 v t pd propagation delay d v/ d t = 0.5 v/ m s - 140 185 ns v swp short-winding protection voltage 0.83 0.88 0.96 v t leb leading edge blanking time 300 370 440 ns i startup(soft) soft startup current v i on pin sense < 0.5 v 45 60 75 m a overvoltage protection (pin 16 and pin 2) i ovp over-voltage protection current [2] 279 300 321 m a i ch(ovpfcap) charge current on pin ovpfcap v i on pin ovpfcap = 1 v [3] - 36 - 32 - 28 m a i dch(ovpfcap) discharge current on pin ovpfcap v i on pin ovpfcap = 1 v [3] 52 60 68 m a v trip(ovpfcap) trip voltage on pin ovpfcap 2.37 2.5 2.63 v t p(ovpfcap) pulse duration on pin ovpfcap 2.3 2.8 3.4 m s table 5. characteristics continued t amb = 25 c; v cc = 15 v; all voltages are measured with respect to ground (pin 11); currents are positive when ?owing into the ic, unless otherwise speci?ed. symbol parameter conditions min typ max unit
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 21 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic [1] guaranteed by design. [2] set by the demagnetization resistor, r dem ; see section 7.9 ov er v oltage protection . [3] set by the ovpfcap capacitor; see section 7.9 ov er v oltage protection . [4] value equal to the product of the ovpfcap current pulse width and the ovp ?lter timing charge current. [5] value equal to the product of the ovpfcap current pulse width and the ovp ?lter timing discharge current. [6] set by the demagnetization resistor, r dem ; see section 7.12 ov er po w er protection . [7] maximum source voltage is limited to 0.3 v. q ovpfcap charge on pin ovpfcap charge delivered [4] - 103 - 90 - 77 pc charge subtracted [5] 145 170 195 pc overpower protection (pin 16) i opp(dem) over-power protection current on pin dem [6] - - 120 - m a i opp(red)(dem) reduced over-power protection current on pin dem v isense < 0.3 v [7] - - 500 - m a stdby output (pin 4) v o(stdby) output voltage on pin stdby 4.75 5.0 5.25 v i source(stdby) source current on pin stdby pin stdby source current, v stdby = 1.5 v - 25 - 22 - 20 m a i sink(stdby) sink current on pin stdby pin stdby sink current, v i on pin stdby = 1.5 v 2--ma driver (pin 5) i source(driver) source current on pin driver pin driver source current, v cc = 9.5 v; v i on pin driver = 2 v - - 170 - 88 ma i sink(driver) sink current on pin driver pin driver sink current, v cc = 9.5 v; v i on pin driver = 2 v - 300 - ma v cc = 9.5 v; v i on pin driver = 9.5 v 400 700 - ma v o(max) maximum output voltage v cc = 12 v - 11.5 12 v temperature protection t pl(max) maximum protection level temperature 130 140 150 c t pl(hys) protection level hysteresis temperature -8 [1] - c table 5. characteristics continued t amb = 25 c; v cc = 15 v; all voltages are measured with respect to ground (pin 11); currents are positive when ?owing into the ic, unless otherwise speci?ed. symbol parameter conditions min typ max unit
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 22 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic 11. application information a converter using the TEA1553T consists of an input ?lter, a transformer with a third winding (auxiliary), and an output stage with a feedback circuit. capacitor c vcc (at pin 9) buffers the supply voltage of the ic, which is powered via the high voltage recti?ed mains during start-up and via the auxiliary winding during operation. a sense resistor converts the primary current into a voltage at pin isense (pin 3). the value of this sense resistor de?nes the maximum primary peak current. (1) the lock pin is used in this example for an additional external overtemperature protection. if this pin is not used, it must be tied to ground. fig 14. application diagram of TEA1553T with controlled pfc 1 2 3 4 5 6 7 8 10 9 12 11 14 13 16 15 TEA1553T output 014aaa013 pfc rs2 rss css v mains dem ctrl lock gnd vcc n.c. vcc5v cstart stdby driver hvs hvs drain isense ovpfcap vcoadj r sense r dem power mosfet q
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 23 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic fig 15. typical waveforms 014aaa014 v in v drain v o v cc v driver v mains(oper(en) v cc5v start-up sequence normal operation ovp normal operation output short-circuit
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 24 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic 12. package outline fig 16. package outline sot109-1 (so16) x w m q a a 1 a 2 b p d h e l p q detail x e z e c l v m a (a ) 3 a 8 9 1 16 y pin 1 index unit a max. a 1 a 2 a 3 b p cd (1) e (1) (1) eh e ll p qz y w v q references outline version european projection issue date iec jedec jeita mm inches 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 10.0 9.8 4.0 3.8 1.27 6.2 5.8 0.7 0.6 0.7 0.3 8 0 o o 0.25 0.1 dimensions (inch dimensions are derived from the original mm dimensions) note 1. plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 1.0 0.4 sot109-1 99-12-27 03-02-19 076e07 ms-012 0.069 0.010 0.004 0.057 0.049 0.01 0.019 0.014 0.0100 0.0075 0.39 0.38 0.16 0.15 0.05 1.05 0.041 0.244 0.228 0.028 0.020 0.028 0.012 0.01 0.25 0.01 0.004 0.039 0.016 0 2.5 5 mm scale so16: plastic small outline package; 16 leads; body width 3.9 mm sot109-1
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 25 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic 13. revision history table 6. revision history document id release date data sheet status change notice supersedes TEA1553T_1 20070703 product data sheet - -
TEA1553T_1 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 01 3 july 2007 26 of 27 nxp semiconductors TEA1553T greenchip ii smps control ic 14. legal information 14.1 data sheet status [1] please consult the most recently issued document before initiating or completing a design. [2] the term short data sheet is explained in section de?nitions. [3] the product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple dev ices. the latest product status information is available on the internet at url http://www .nxp .com . 14.2 de?nitions draft the document is a draft version only. the content is still under internal review and subject to formal approval, which may result in modi?cations or additions. nxp semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. short data sheet a short data sheet is an extract from a full data sheet with the same product type number(s) and title. a short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. for detailed and full information see the relevant full data sheet, which is available on request via the local nxp semiconductors sales of?ce. in case of any inconsistency or con?ict with the short data sheet, the full data sheet shall prevail. 14.3 disclaimers general information in this document is believed to be accurate and reliable. however, nxp semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. right to make changes nxp semiconductors reserves the right to make changes to information published in this document, including without limitation speci?cations and product descriptions, at any time and without notice. this document supersedes and replaces all information supplied prior to the publication hereof. suitability for use nxp semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of a nxp semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. nxp semiconductors accepts no liability for inclusion and/or use of nxp semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customers own risk. applications applications that are described herein for any of these products are for illustrative purposes only. nxp semiconductors makes no representation or warranty that such applications will be suitable for the speci?ed use without further testing or modi?cation. limiting values stress above one or more limiting values (as de?ned in the absolute maximum ratings system of iec 60134) may cause permanent damage to the device. limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the characteristics sections of this document is not implied. exposure to limiting values for extended periods may affect device reliability. terms and conditions of sale nxp semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www .nxp .com/pro? le/ter ms , including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by nxp semiconductors. in case of any inconsistency or con?ict between information in this document and such terms and conditions, the latter will prevail. no offer to sell or license nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. 14.4 trademarks notice: all referenced brands, product names, service names and trademarks are the property of their respective owners. greenchip is a trademark of nxp b.v. 15. contact information for additional information, please visit: http://www .nxp.com for sales of?ce addresses, send an email to: salesad dresses@nxp.com document status [1] [2] product status [3] de?nition objective [short] data sheet development this document contains data from the objective speci?cation for product development. preliminary [short] data sheet quali?cation this document contains data from the preliminary speci?cation. product [short] data sheet production this document contains the product speci?cation.
nxp semiconductors TEA1553T greenchip ii smps control ic ? nxp b.v. 2007. all rights reserved. for more information, please visit: http://www.nxp.com for sales office addresses, please send an email to: salesaddresses@nxp.com date of release: 3 july 2007 document identifier: TEA1553T_1 please be aware that important notices concerning this document and the product(s) described herein, have been included in section legal information. 16. contents 1 general description . . . . . . . . . . . . . . . . . . . . . . 1 2 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.1 distinctive features . . . . . . . . . . . . . . . . . . . . . . 1 2.2 green features . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.3 protection features . . . . . . . . . . . . . . . . . . . . . . 1 3 applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 4 ordering information . . . . . . . . . . . . . . . . . . . . . 2 5 block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 6 pinning information . . . . . . . . . . . . . . . . . . . . . . 4 6.1 pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 6.2 pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 7 functional description . . . . . . . . . . . . . . . . . . . 5 7.1 start-up, mains enabling operation level and undervoltage lock-out . . . . . . . . . . . . . . . . . . . . 6 7.2 supply management. . . . . . . . . . . . . . . . . . . . . 6 7.3 current mode control . . . . . . . . . . . . . . . . . . . . 7 7.4 oscillator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 7.5 vco adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 7.6 cycle skipping. . . . . . . . . . . . . . . . . . . . . . . . . . 9 7.7 stdby output. . . . . . . . . . . . . . . . . . . . . . . . . . 9 7.8 demagnetization. . . . . . . . . . . . . . . . . . . . . . . 10 7.9 overvoltage protection . . . . . . . . . . . . . . . . . . 10 7.10 valley switching. . . . . . . . . . . . . . . . . . . . . . . . 11 7.11 overcurrent protection . . . . . . . . . . . . . . . . . . 12 7.12 overpower protection . . . . . . . . . . . . . . . . . . . 12 7.13 advanced overpower timing via pin cstart . 13 7.14 minimum and maximum on-time . . . . . . . . . . 14 7.15 short winding protection . . . . . . . . . . . . . . . . . 14 7.16 lock input . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 7.17 overtemperature protection . . . . . . . . . . . . . . 15 7.18 5 v output . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 7.19 open/not connected ctrl pin protection . . . 15 7.20 soft start-up (pin isense) . . . . . . . . . . . . . . . 15 7.21 driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 8 limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 17 9 thermal characteristics. . . . . . . . . . . . . . . . . . 18 10 characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 18 11 application information. . . . . . . . . . . . . . . . . . 22 12 package outline . . . . . . . . . . . . . . . . . . . . . . . . 24 13 revision history . . . . . . . . . . . . . . . . . . . . . . . . 25 14 legal information. . . . . . . . . . . . . . . . . . . . . . . 26 14.1 data sheet status . . . . . . . . . . . . . . . . . . . . . . 26 14.2 de?nitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 14.3 disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 14.4 trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 15 contact information . . . . . . . . . . . . . . . . . . . . 26 16 contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

▲Up To Search▲

Price & Availability of TEA1553T

	To Download TEA1553T Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .